A magnet surrounding the detectors bends the paths of charged particles. This shows if they are positively - or negatively- charged and also allows their momentum to be measured. Inside ATLAS, the solenoid magnet surrounding the tracking detectors must be as thin as possible, so as not to affect their measurements. 9 km of superconducting wires, support casing, cooling fluids and insulation is squeezed into the 4.5 cm gap between the tracking detectors and the calorimeters. ATLAS is one of the 4 large experiments surrounding collision points at the Large Hadron Collider.

A magnet surrounding the detectors bends the paths of charged particles. This shows if they are positively - or negatively- charged and also allows their momentum to be measured. Inside ATLAS, the solenoid magnet surrounding the tracking detectors must be as thin as possible, so as not to affect their measurements. 9 km of superconducting wires, support casing, cooling fluids and insulation is squeezed into the 4.5 cm gap between the tracking detectors and the calorimeters. ATLAS is one of the 4 large experiments surrounding collision points at the Large Hadron Collider.

Each of these straws is a complete mini–detector in its own right. Every one is filled with a gas mixture and threaded with a wire. Imagine assembling 300’000 fragile drinking straws up to 144 cm long, with no bends or kinks allowed! This layer of tracker plays two important roles. Firstly, it makes more position measurements, giving more dots for the computers to join up to recreate the particle tracks. Then it also helps distinguish between different types of particles depending on whether they emit radiation as they make the transition from the surrounding foil into the straws. An electric field is applied between the wire and the outside wall of the straw. As particles pass through, they collide with atoms in the gas, knocking out electrons. The avalanche of electrons is detected as an electrical signal on the wire in the centre.

Each of these straws is a complete mini–detector in its own right. Every one is filled with a gas mixture and threaded with a wire. Imagine assembling 300’000 fragile drinking straws up to 144 cm long, with no bends or kinks allowed! This layer of tracker plays two important roles. Firstly, it makes more position measurements, giving more dots for the computers to join up to recreate the particle tracks. Then it also helps distinguish between different types of particles depending on whether they emit radiation as they make the transition from the surrounding foil into the straws. An electric field is applied between the wire and the outside wall of the straw. As particles pass through, they collide with atoms in the gas, knocking out electrons. The avalanche of electrons is detected as an electrical signal on the wire in the centre.

42 modules like this one surround the collision point inside the LHCb detector. Their role is to measure the tracks of short-lived particles spraying out from the collision and to pinpoint the exact spots where they decay into secondary particles. Some exist for just trillionths of a second before decaying! The silicon modules operate so close to the collision point, they can only be moved into position once the circling particle beams are at their most focused. Otherwise, peripheral particles on the outside of the finer-than-a-hair beam would bore a hole right through them.

LHCb measures muons using gold plated tungsten wires stretched over read-out pads. A high voltage is applied across the wires and pads and the set-up is bathed in a gas mixture. Passing muons interact with the gas, knocking out electrons from its atoms in a process called ionization. Both the ionized atoms and the electrons then drift in the electric field. This movement creates an electric signal in the wires and pads that is used to identify where the muon has passed. In total, the LHCb muon detectors contain about 2 million wires and are capable of making measurements 40 million times a second – every time the particle beams collide.

The CMS (Compact Muon Solenoid) Tile Calorimeter is a pivotal component of the CMS detector, which is one of the major experiments at the Large Hadron Collider (LHC) at CERN. Designed to measure the energy of particles, the calorimeter plays an essential role in the study of high-energy physics.

The CMS (Compact Muon Solenoid) Tile Calorimeter is a pivotal component of the CMS detector, which is one of the major experiments at the Large Hadron Collider (LHC) at CERN. Designed to measure the energy of particles, the calorimeter plays an essential role in the study of high-energy physics.